[求助]停车场地感线圈的安装请教...

我现在涉及到一个5.4米宽的道路，要在上面切一个地感线圈，听说2.5的线绕长只能是30m左右，太长了不行。于是我想按平行四边形来做，想请教大家一下，具体平行四边形的大小和道宽有什么关系？该怎么定这个大小？（四边形是45度的，如果不合适请帮我提一个解决方案），多谢了！

中国一卡通网 · 发表于 2007-11-6 17:04:00

停车场管理系统接线图说明书 <a href="http://bbs.yktchina.com/disptopic.asp?boardid=8&topicid=1444&frompage=1">http://bbs.yktchina.com/disptopic.asp?boardid=8&topicid=1444&frompage=1</a>智能停车场系统_管线图 <a href="http://bbs.yktchina.com/disptopic.asp?boardid=8&topicid=1443&frompage=1">http://bbs.yktchina.com/disptopic.asp?boardid=8&topicid=1443&frompage=1</a>不知道有没有用，供楼主参考一下吧<a href="http://www.yktchina.com/" target="_blank"><img alt="图片点击可在新窗口打开查看" src="http://www.yktchina.com/inc/UploadFile/2007911175138801.gif" border="0" style="CURSOR: pointer;"/></a>

lvtaohua · 发表于 2007-11-6 17:45:00

多谢，我现在就看看

ascentech · 发表于 2007-11-7 15:18:00

线圈安装规范及故障处理线圈安装规范：一、1．        线圈和馈线应该用绝缘铜线（最小横截面积1.5平方毫米）制作。2．  馈线应该每米至少双绞20圈。3．  应该尽量避免焊接点，万不得已则必须良好接触并做好绝缘。4．  非良好的连接点将导致线圈检测器误操作。5．  馈线将受到外界电磁干扰，所以应该使用屏蔽电缆，屏蔽电缆的屏蔽线在线圈检测器端良好接地。二、1．      线圈如表线圈埋法示意图。2．      线圈匝数及电感量见下表1。三、<p class="MsoNormal" style="MARGIN: 0cm 0cm 0pt 45.05pt; TEXT-INDENT: -36.15pt; LINE-HEIGHT: 150%; mso-list: l3 level1 lfo3; tab-stops: list 18.0pt; mso-char-indent-count: -3.43; mso-para-margin-left: .85gd;">1．           串扰是指两个相邻线圈的馈线或与电源220v之间的至相互干涉。解决的办法为馈线必须双绞，如与供电电源在同一管道内，则馈线必须加屏蔽电缆，并使屏蔽层在一端良好接地（接地电阻不大于5Ω）。2．            为了避免线圈检测器误操作，线圈之间应至少相隔0.3米，并做不同的频率设定。四、1．            所需设备为路面线槽切割工具；2．            为了保护线圈在直角处不被损坏，在直角处应按两个45度角的切割。3．            线槽应该8mm宽，30mm到40mm深。4．            注意从线圈的一角到路边延伸线槽以放馈线五、<p class="MsoNormal" style="MARGIN: 0cm 0cm 0pt 44.9pt; TEXT-INDENT: -36pt; LINE-HEIGHT: 150%; mso-list: l1 level1 lfo5; tab-stops: list 18.0pt; mso-char-indent-count: -3.43; mso-para-margin-left: .85gd;">1．            为了达到最好的效果，应该使用一整根没有接点的电线，从检测器引出，到路面线圈再返回到检测器。2．            应该记住的是：双绞馈线会缩短电线的长度，所以应保证足够长的电线。六、1．            线圈和馈线安放好以后，缝隙应该用沥青填充物充分填好。    表1 ：线圈及馈线横截面积：1.5mm²,电阻率：1.678x10<shapetype id="_x0000_t75" stroked="f" filled="f" path="m@4@5l@4@11@9@11@9@5xe" opreferrelative="t" ospt="75" coordsize="21600,21600">
<stroke joinstyle="miter"></stroke><formulas><f eqn="if lineDrawn pixelLineWidth 0"></f><f eqn="sum @0 1 0"></f><f eqn="sum 0 0 @1"></f><f eqn="prod @2 1 2"></f><f eqn="prod @3 21600 pixelWidth"></f><f eqn="prod @3 21600 pixelHeight"></f><f eqn="sum @0 0 1"></f><f eqn="prod @6 1 2"></f><f eqn="prod @7 21600 pixelWidth"></f><f eqn="sum @8 21600 0"></f><f eqn="prod @7 21600 pixelHeight"></f><f eqn="sum @10 21600 0"></f></formulas><path oconnecttype="rect" gradientshapeok="t" oextrusionok="f"></path><lock aspectratio="t" vext="edit"></lock></shapetype><shape id="_x0000_i1025" oole="" type="#_x0000_t75" style="WIDTH: 11.25pt; HEIGHT: 15pt;"><imagedata otitle="" src="file:///C:\DOCUME~1\ADMINI~1\LOCALS~1\Temp\msohtml1\01\clip_image001.wmz"></imagedata></shape> <table class="MsoTableGrid" cellspacing="0" cellpadding="0" border="1" style="BORDER-RIGHT: medium none; BORDER-TOP: medium none; BORDER-LEFT: medium none; BORDER-BOTTOM: medium none; BORDER-COLLAPSE: collapse; mso-border-alt: solid windowtext .5pt; mso-yfti-tbllook: 480; mso-padding-alt: 0cm 5.4pt 0cm 5.4pt; mso-border-insideh: .5pt solid windowtext; mso-border-insidev: .5pt solid windowtext;"><tbody><tr style="mso-yfti-irow: 0; mso-yfti-firstrow: yes;"><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: windowtext 1pt solid; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: windowtext 1pt solid; WIDTH: 85.2pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt;">馈线+引线长度</td><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: windowtext 1pt solid; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: #ece9d8; WIDTH: 85.2pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-left-alt: solid windowtext .5pt;">0米-50米</td><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: windowtext 1pt solid; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: #ece9d8; WIDTH: 85.2pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-left-alt: solid windowtext .5pt;">50米-100米</td><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: windowtext 1pt solid; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: #ece9d8; WIDTH: 85.25pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-left-alt: solid windowtext .5pt;">100米-150米</td><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: windowtext 1pt solid; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: #ece9d8; WIDTH: 85.25pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-left-alt: solid windowtext .5pt;">150米-200米</td></tr><tr style="mso-yfti-irow: 1;"><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: #ece9d8; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: windowtext 1pt solid; WIDTH: 85.2pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-top-alt: solid windowtext .5pt;">线圈匝数</td><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: #ece9d8; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: #ece9d8; WIDTH: 85.2pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-left-alt: solid windowtext .5pt; mso-border-top-alt: solid windowtext .5pt;">3</td><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: #ece9d8; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: #ece9d8; WIDTH: 85.2pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-left-alt: solid windowtext .5pt; mso-border-top-alt: solid windowtext .5pt;">4</td><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: #ece9d8; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: #ece9d8; WIDTH: 85.25pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-left-alt: solid windowtext .5pt; mso-border-top-alt: solid windowtext .5pt;">5</td><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: #ece9d8; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: #ece9d8; WIDTH: 85.25pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-left-alt: solid windowtext .5pt; mso-border-top-alt: solid windowtext .5pt;">6</td></tr><tr style="mso-yfti-irow: 2;"><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: #ece9d8; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: windowtext 1pt solid; WIDTH: 85.2pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-top-alt: solid windowtext .5pt;">电感量</td><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: #ece9d8; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: #ece9d8; WIDTH: 85.2pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-left-alt: solid windowtext .5pt; mso-border-top-alt: solid windowtext .5pt;">100μH-200μH</td><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: #ece9d8; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: #ece9d8; WIDTH: 85.2pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-left-alt: solid windowtext .5pt; mso-border-top-alt: solid windowtext .5pt;">200μH-250μH</td><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: #ece9d8; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: #ece9d8; WIDTH: 85.25pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-left-alt: solid windowtext .5pt; mso-border-top-alt: solid windowtext .5pt;">250μH-300μH</td><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: #ece9d8; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: #ece9d8; WIDTH: 85.25pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-left-alt: solid windowtext .5pt; mso-border-top-alt: solid windowtext .5pt;">300μH以上</td></tr><tr style="mso-yfti-irow: 3; mso-yfti-lastrow: yes;"><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: #ece9d8; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: windowtext 1pt solid; WIDTH: 85.2pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-top-alt: solid windowtext .5pt;">电阻值</td><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: #ece9d8; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: #ece9d8; WIDTH: 85.2pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-left-alt: solid windowtext .5pt; mso-border-top-alt: solid windowtext .5pt;">≤3Ω</td><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: #ece9d8; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: #ece9d8; WIDTH: 85.2pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-left-alt: solid windowtext .5pt; mso-border-top-alt: solid windowtext .5pt;">≤6Ω</td><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: #ece9d8; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: #ece9d8; WIDTH: 85.25pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-left-alt: solid windowtext .5pt; mso-border-top-alt: solid windowtext .5pt;">≤9Ω</td><td valign="top" width="114" style="BORDER-RIGHT: windowtext 1pt solid; PADDING-RIGHT: 5.4pt; BORDER-TOP: #ece9d8; PADDING-LEFT: 5.4pt; PADDING-BOTTOM: 0cm; BORDER-LEFT: #ece9d8; WIDTH: 85.25pt; PADDING-TOP: 0cm; BORDER-BOTTOM: windowtext 1pt solid; BACKGROUND-COLOR: transparent; mso-border-alt: solid windowtext .5pt; mso-border-left-alt: solid windowtext .5pt; mso-border-top-alt: solid windowtext .5pt;">≤12Ω</td></tr></tbody></table>

ascentech · 发表于 2007-11-7 15:20:00

线圈的大小并没什么,主要是线圈之间不要小于50cm,同时出来的馈线双绞.

jinyindao · 发表于 2007-11-7 23:05:00

有用地感的和我联系，真便宜，质量没说的！这里不方便报价．ＱＱ３７５７８７５８７手机１３６９７４６５５６２　　szgicc2008@163.com

ascentech · 发表于 2007-11-13 09:57:00

一个5.4米宽的道路，要在上面切一个地感线圈----------为了不漏车,你切5米长也没关系,记得线圈出来的双绞线必须双绞,  应该尽量避免焊接点，万不得已则必须良好接触并做好绝缘。<span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ascii-font-family: 'Times New Roman'; mso-bidi-font-size: 12.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">线圈和馈线应该用绝缘铜线（最小横截面积<span lang="EN-US" style="FONT-SIZE: 10.5pt; FONT-FAMILY: "Times New Roman"; mso-font-kerning: 1.0pt; mso-bidi-font-size: 12.0pt; mso-fareast-font-family: 宋体; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">1.5<span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ascii-font-family: 'Times New Roman'; mso-bidi-font-size: 12.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">平方毫米）制作   听说2.5的线绕长只能是30m左右，太长了不行。--我们的车辆检测器最远1000米也没关系但是相应的圈数要增加.1000米可能是要10圈了.  于是我想按平行四边形来做，想请教大家一下，具体平行四边形的大小和道宽有什么关系？该怎么定这个大小？-------其实这个是为了防止漏车,具体形状其实要求并不严格.但是最好2个相邻线圈距离大于50CM.     为了保护线圈在直角处不被损坏，在直角处应按两个45度角的切割。<span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ascii-font-family: 'Times New Roman'; mso-bidi-font-size: 12.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">线槽应该<span lang="EN-US" style="FONT-SIZE: 10.5pt; FONT-FAMILY: "Times New Roman"; mso-font-kerning: 1.0pt; mso-bidi-font-size: 12.0pt; mso-fareast-font-family: 宋体; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">8mm<span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ascii-font-family: 'Times New Roman'; mso-bidi-font-size: 12.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">宽，<span lang="EN-US" style="FONT-SIZE: 10.5pt; FONT-FAMILY: "Times New Roman"; mso-font-kerning: 1.0pt; mso-bidi-font-size: 12.0pt; mso-fareast-font-family: 宋体; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">30mm<span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ascii-font-family: 'Times New Roman'; mso-bidi-font-size: 12.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">到<span lang="EN-US" style="FONT-SIZE: 10.5pt; FONT-FAMILY: "Times New Roman"; mso-font-kerning: 1.0pt; mso-bidi-font-size: 12.0pt; mso-fareast-font-family: 宋体; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">40mm<span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ascii-font-family: 'Times New Roman'; mso-bidi-font-size: 12.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">深.<span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ascii-font-family: 'Times New Roman'; mso-bidi-font-size: 12.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">     注意:     串扰是指两个相邻线圈的馈线或与电源220v之间的至相互干涉。解决的办法为馈线必须双绞，如与供电电源在同一管道内，则馈线必须加屏蔽电缆，并使屏蔽层在一端良好接地（接地电阻不大于5Ω）。<span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ascii-font-family: 'Times New Roman'; mso-bidi-font-size: 12.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">    另外每家线圈车辆检测器的具体要求不一样,我只是说明我的车辆检测器的大致对线圈的要求.线圈切割很重要,同样,车辆检测器自身的抗干扰能力及灵敏度也是非常重要的.<span style="FONT-SIZE: 10.5pt; FONT-FAMILY: 宋体; mso-hansi-font-family: 'Times New Roman'; mso-bidi-font-family: 'Times New Roman'; mso-font-kerning: 1.0pt; mso-ascii-font-family: 'Times New Roman'; mso-bidi-font-size: 12.0pt; mso-ansi-language: EN-US; mso-fareast-language: ZH-CN; mso-bidi-language: AR-SA;">     <a href="http://www.ascentech.sh.cn">www.ascentech.sh.cn</a>    罗承志  我们只做线圈车辆检测器.不做别的.也做不好别的产品.

kouyanhui · 发表于 2007-12-26 09:12:00

[此贴子已经被作者于2012/3/15 17:45:57编辑过]

wei1979 · 发表于 2007-12-26 11:56:00

各家地感线有些不同,切平行四边形的时候记得转角,不要伤线派威为你提供安全可靠的停车场设备,真诚为你服务 联系电话:13224073879(彭伟) QQ:78351227

szhst · 发表于 2007-12-27 17:38:00

不错啊，

tpkj_gl · 发表于 2007-12-30 18:07:00

长知识了,原来对停车场真的不太熟悉

AShevchenko · 发表于 2008-1-3 15:09:00

地感很重要,很重要

kevin482 · 发表于 2010-2-1 21:15:00

刚接触，学习了。

xiaolidong · 发表于 2011-1-25 16:53:00

不错

石头疯了 · 发表于 2011-1-27 11:41:00

不错

knife0506 · 发表于 2011-1-29 09:33:00

不错打酱油

vicming · 发表于 2011-1-30 12:33:00

上面说得很具体，又学习到不少知识，谢谢

门禁/对讲/一卡通今日: 1847 |主题: 18133

[求助]停车场地感线圈的安装请教...

已有16人评论

本帖子中包含更多资源

门禁/对讲/一卡通 今日: 1847 |主题: 18133

[求助]停车场地感线圈的安装请教...

已有16人评论

本帖子中包含更多资源

门禁/对讲/一卡通今日: 1847 |主题: 18133