４００６ＢＧＩＣ模块问题，请高进来指点，在线等，...

想在业务板上3/1 3/2 连两个ＢＧＩＣ模块，出现的问题是，把3/1 和3/2加入ＶＬＡＮ４后，整个网络都断了，不知道为啥，请高手进来看一看！ 4006 show run This command shows non-default configurations only. Use 'show config all' to show both default and non-default configurations. ............. .................. .................. .................... .. begin ! # ***** NON-DEFAULT CONFIGURATION ***** ! ! #time: Thu Mar 16 2006, 21:22:41 ! #version 6.3(3a) ! ! #system web interface version(s) set password $2$cNWO$7i0Vfg2L3hM7FQCXL4Hyz. --More--        ! #test ! #frame distribution method set port channel all distribution mac both ! #vtp set vtp domain library set vtp mode transparent set vlan 1 name default type ethernet mtu 1500 said 100001 state active set vlan 2 name trunk type ethernet mtu 1500 said 100002 state active set vlan 3 name uplink type ethernet mtu 1500 said 100003 state active set vlan 4 name library-network type ethernet mtu 1500 said 100004 state active set vlan 1002 name fddi-default type fddi mtu 1500 said 101002 state active set vlan 1004 name fddinet-default type fddinet mtu 1500 said 101004 state active stp ieee set vlan 1005 name trnet-default type trbrf mtu 1500 said 101005 state active stp ibm set vlan 1003 name token-ring-default type trcrf mtu 1500 said 101003 state active mode srb aremaxhop 7 stemaxhop 7 backupcrf off ! #ip set interface sl0 down set interface me1 down ! #spantree --More--        #vlan <VlanId> ! #syslog set logging level cops 2 default ! #set boot command set boot config-register 0x2 set boot system flash bootflash:cat4000.6-3-3a.bin ! #module 1 : 2-port 1000BaseX Supervisor set vlan 3 1/1 set vlan 4 1/2 ! #module 2 : 6-port 1000BaseX Ethernet set vlan 4 2/1-6 ! #module 3 : 34-port Router Switch Card set vlan 2 3/1-2 set vlan 4 3/3-34 set trunk 3/1 on dot1q 1-1005 set trunk 3/2 on dot1q 1-1005 ! #module 4 empty --More--        ! #module 5 empty ! #module 6 empty end Console> (enable) show ip int b Show ip commands: ---------------------------------------------------------------------------- show ip alias Show aliases for IP Addresses show ip dns Show IP DNS information show ip route Show IP routing table show ip http Show IP HTTP information show ip permit Show IP Permit List Console> (enable) 2006 Mar 16 21:22:48 %SYS-4-P2_WARN: 1/Host 02:01:00:00:00:00 is flapping between port 2/1 and port 3/3 Console> (enable) Console> (enable) Console> (enable) Building configuration... Current configuration: ! version 12.0 no service pad service timestamps debug uptime service timestamps log uptime no service password-encryption ! hostname library-4006 ! enable password 4006 ! ip subnet-zero ! ! ! interface FastEthernet1 no ip address no ip directed-broadcast shutdown ! interface GigabitEthernet1 --More--   no ip address no ip directed-broadcast ! interface GigabitEthernet2 no ip address no ip directed-broadcast shutdown ! interface GigabitEthernet3 no ip address no ip directed-broadcast no negotiation auto ! interface GigabitEthernet3.1 encapsulation dot1Q 1 native no ip redirects no ip directed-broadcast ! interface GigabitEthernet3.3 encapsulation dot1Q 3 ip address 2.2.2.2 255.255.255.252 ip access-group 110 in ip access-group 110 out --More--   no ip redirects no ip directed-broadcast ! interface GigabitEthernet3.4 encapsulation dot1Q 4 ip address 1.1.1.1 255.255.255.0 secondary no ip redirects no ip directed-broadcast ! interface GigabitEthernet4 no ip address no ip directed-broadcast no negotiation auto ! router ospf 1 passive-interface FastEthernet1 network 1.1.1.0 0.0.0.255 area 0 ip classless ip route 0.0.0.0 0.0.0.0 1.1.1.1