MA5605配置操作手册
相关命令：show time
show version
show board 0
show running-config
1:改名字
MA5605(config)#hostname xiaowei
2:改用户密码
MA5605#user password
>old password: admin
> New password(<20 chars): adminmin（改后新密码，如果不需要设置此步不需要做）
> Confirm new password:adminmin
3:改时间
MA5605#time （一般不用配置）
4. 进入LAN 配置模式设置LAN 端口状态
int lan 0/0
MA5605(config-LAN-0/0)#port mode
<tagged-mode>{tagged,untagged}:tagged
{negotiate,non-negotiate}:non-negotiate
{full-duplex}:full-duplex
<speed>{100m}:100m
Set successfully.
5.MA5605(config-LAN-0/0)#vlan %d (业务VLAN）
<vlanId>{1-4095}:1554
Add VLAN successfully, VLANID =
MA5605(config-LAN-0/0)#vlan %d (管理VLAN）
<vlanId>{1-4095}:1000
Add VLAN successfully, VLANID =
5. 设置VLAN (打开带内通道)
MA5605(config)#nms
<vlanId>{1-4095}:1000（网关vlan）
Are you sure to set the inband VLAN to 1? (y/n) [n]:y
6. 设置级联转发VLAN (注意如果是级连要此步，不是侧不要)
MA5605(config-LAN-0/0)#cascade
{forward,number}:number
<num>{0-3}:1
Set cascading number successfully.
MA5605(config-LAN-0/0)#cascade
{forward,number}:forward
{vlan,all}:all
<start-vlanId>{1-4095}:
<end-vlanId>{1-4095}:
Set 16 cascading VLAN successfully.
注意：
?? 如果有级联设备，则上级设备需要设置转发（下级设备的）VLAN和级联层数（
设置FE接口级联转发功能”）；
?? 级联MA5605 下级的VLAN ID 必须在上级MA5605 设备分配的范围内。
7. 设置设备IP 地址
MA5605(config)#atmlan ip-address ethernet
<ip-addr>:218.92.157.150
<netmask>:255.255.255.248
Set successfully
8. 配置到上连设备的系统路由
MA5605(config)#atmlan ip-route
<ip-addr>:0.0.0.0
<netmask>:0.0.0.0
<gateway>:218.92.157.145
Add route successfully.
9. 配置可接受访问列表
MA5605(config)#atmlan ip-access
<start-ip>:218.92.157.145 (路游地址)
<end-ip>:218.92.157.137
<mask>:255.255.255.255
（可把县局要维护的计算机、交换机地址配置进去）
10. 设置ADSL 线路模板参数
WA_SL_MA5605(config)#adsl line-profile add 8
During input,press 'Q' to quit,then settings at this time are neglected.
> Select the line profile type 1-adsl 2-adsl2+(1~2) [1]: (2加模板)
> Will you set basic configuration for modem? (y/n) [n]:y
Note: Setting to these mode of G992.3~5 will lead that the adsl ports that are
not support adsl2+ not be activated
> ADSL operating mode:
> 0: All(G992.1~3, G992.5, T1.413)
> 1: Full rate(G992.1/3/5 or T1.413)
> 2: g.lite(G992.2) (ADLI can not support )
> 3: T1.413 (ADLI can not support )
> 4: g.dmt(G992.1/3/5)
> 5: g.hs(G992.1~3, G992.5, G992.5 is prior)
> 6: G992.1
> 7: G992.2 (ADLI can not support )
> 8: G992.3
> 9: G992.5
Please select (0~9) [0]:
> Trellis coding 0-disable 1-enable (0~1) [1]:
> Upstream channel bit swap 0-disable 1-enable (0~1) [1]:
> Downstream channel bit swap 0-disable 1-enable (0~1) [1]: 0
> Will you set channel mode? (y/n) [n]: y
Please select channel mode 0-interleaved 1-fast (0~1) [0]:
> Will you set interleave delay? (y/n) [n]: y
> Max down stream interleaved delay(0~255 ms) [16]:
> Max up stream interleaved delay(0~255 ms) [6]:
> Please select form of transmit rate adaptation in downstream:
> 0-fixed 1-adaptAtStartup 2-adaptAtRuntime (0~2) [1]:
> Will you set noise margin for modem? (y/n) [n]:y
> Target noise margin in down stream (0~15 dB) [6]:
> Min noise margin in down stream (0~6 dB) [0]:
> Max noise margin in down stream (6~31 dB) [31]:
> Target noise margin in up stream (0~15 dB) [6]:
> Min noise margin in up stream (0~6 dB) [0]:
> Max noise margin in up stream (6~31 dB) [31]:
> Will you set parameters for rate? (y/n) [n]: y
> Min bit rate in down stream (32~32000 Kbps) [32]:
> Max bit rate in down stream (32~32000 Kbps) [32000]: 7168（下行用户速率）
> Min bit rate in up stream (32~3000 Kbps) [32]:
> Max bit rate in up stream (32~3000 Kbps) [3000]: 512（上行速率）
> Please input the profile's name : 9M
Add profile 9 successfully.
12. 激活ADSL 端口
MA5605(config)#interface adsl 0/1
MA5605(config-ADSL-0/1)#detactivate all
MA5605(config-ADSL-0/1)#activate
{<all>}{all}:all
[<lineprofileindex>]{1-20}:5
13. 设置从ADSL 1 端口到VLAN 10 的业务PVC pvc adsl 0/1/1 8 81 lan 0/0 2335 1483b 1 off off 2 2 (批量生成)
MA5605(config)#pvc
{adsl,shdsl,lan}:adsl
<FrameId/SlotId/PortId>{(0)/(1-4)/(1-16)}:0/1/1
{<vpi>}{0-127}:0
{<vci>}{32-127}:100
{adsl,shdsl,lan}:lan
<FrameId/SlotId>{(0)/(0-4)}:0/0
{untagged,tagged}:tagged
<vlanId>{1-4095}:10
{1483b,ipoa}:1483b
<priority>{0-7}:1
<rx-car>{off,on}[on]:off
<tx-car>{off,on}[on]:off
<rx-cttr>{1-20}:2
<tx-cttr>{1-20}:2
15: 保存
MA5605(config)#save
| 欢迎光临 千家论坛_智能建筑与智能家居技术交流社区 (http://bbs.qianjia.com:8020/) | Powered by Discuz! X3.2 |