千家论坛_智能建筑与智能家居技术交流社区

标题: [求助] 西门子控制器中的自适应控制ADAPTM 和ADAPTS [打印本页]

作者: swordoh 时间: 2011-1-12 15:39
标题: [求助] 西门子控制器中的自适应控制ADAPTM 和ADAPTS
请问在实际中应用过吗？各个参数的设置经验。。。。谢谢

作者: swordoh 时间: 2011-1-12 15:41
00010 C ADAPTM
02000 C ADAPTM CONTROL LOOP STATISTICS (LOGICAL FIRMWARE) 02004 C DIRECT CONTROL LOOP 02008 C INPUT = %X%SAT 02012 C Output = %X%VRT 02016 C SETPOINT = %X%SAS 02020 C  MA TEMP CNTRL OUTPUT = $MATCTL 02024 C MA MIN POSITION = %X%MAM 02028 C SAMPLE TIME = 5 SECONDS 02032 C GAIN = %X%KC1 02036 C DAMPER TIME CONSTANT = %X%TD1 02040 C HEATING TIME CONSTANT = %X%TH1 02044 C COOLING TIME CONSTANT = %X%TC1 02048 C HEATING END OF RANGE = 45.0 02052 C DAMPER BEGIN RANGE = 50.0 02056 C DAMPER END RANGE = 65.0 02060 C ERROR REPORT POINT = %X%ER1 02064 ADAPTM("%X%SAT","%X%VRT","%X%SAS","$MATCTL","%X%MAM",5,"%X%KC1","%X%TD1","%X%TH1","%X%TC1",45.0,50.0,65.0,"%X%ER1") 02068 C  HEATING COIL SIGNAL 02072 TABLE("%X%VRT","%X%HCO",0,100,45,0) 02076 C DAMPER RAMP 02080 TABLE("$MADRMP","$MADRCT",0,0,10,"%X%MAM",180,100) 02084 C  DAMPER CONTROL SIGNAL 02088 TABLE("%X%VRT","$MADCTL",50,"%X%MAM",65,100) 02092 C  MIXED AIR TEMPERATURE CONTROL LOOP 02096 IF("$MADRCT" .LT. "$MATCTL") THEN GOTO 2108 02100 ADAPTS("%X%MAT","$MATCTL","%X%MLS",10,"%X%KC2","%X%TM2",0,30.0,130.0,0.0,100.0,0.0,0.0,"%X%ER2") 02104 C ECONOMIZER CONTROL 02108 IF("%X%ECM" .EQ. OFF) THEN GOTO 2136 02112 C COOLING COIL SIGNAL (ECON=ON) 02116 TABLE("%X%VRT","%X%CCO",65,0,100,100) 02120 C FINAL DAMPER SIGNAL 02124 MIN("%X%MAO","$MADRCT","$MADCTL","$MATCTL") 02128 GOTO 2140 02132 C COOLING COIL SIGNAL 02136 TABLE("%X%VRT","%X%CCO",55,0,100,100) 02140 GOTO 10

作者: swordoh 时间: 2011-1-12 15:44
以上是help中的程序。请问$MATCTL 在ADAPTM 和 ADAPTS均出现，各代表的意思。
还有%X%ER1是用来干什么的。

作者: swordoh 时间: 2011-1-12 15:44
请大家指教。。。

作者: wudingshi 时间: 2011-1-17 14:23
  没有用过这样的东西，<a href="http://www.le880.com/">光端机报价</a>

欢迎光临千家论坛_智能建筑与智能家居技术交流社区 (http://bbs.qianjia.com:8020/)