千家论坛_弱电智能化技术与工程讨论(建筑智能,家居智能,人工智能)

电话交换机(PABX)
收藏本版 (3) |订阅

电话交换机(PABX) 今日: 2023 |主题: 11205|排名: 45 

发新帖
打印 上一主题 下一主题

北电交换机工程师帮忙会诊一下Error message from N...

[复制链接]
coben 发布于: 2004-5-12 18:45 1027 次浏览 11 位用户参与讨论
跳转到指定楼层

能判断出是哪的故障吗?怎么解决?经常不定期有电话打不去 BERR705 EXC 0: Exception 14 in Task "pdtShell02" (0x7991248) SR=0x10286, PC=0x1a8f2b5, Addr(CR2)=0xeeeeeeee, ErrCode=0x0,ValidFlags=0x3

SRPT786 RST 0: Task pdtShell02 being restarted

-------------------------------------------------------------------------------------------------------------------------------

Message "aaaa" received from a Network Card (NT8D04). The possible messages are:

1. PLL UNLOCK EVENT. The Network card lost synch with the system clock. 2. MSG FROM SHELF x: XPEC ERROR 0001. This error is usually self correcting. If may indicate a double timeslot problem or invalid call teardown. 3. TN READ UNBLOCKED: CNT=x. A number of SSD messages were sent to the PS card but not acknowledged. In order to prevent the locking of the message path, the Network card assumed the message was received. 4. Any of the following three messages:

XNET POLLING FAILURE ON PORT x RSIG LINK LOST ON PORT #x - REINITIALIZED R71 DISASTER; CANNOT ALIGN TRANSCEIVERS.

These messages indicate that the Controller is not responding to the Network card polling messages.

Ignore if message occur when clocks are switched. If it occurs periodically, switch the clocks. If it occurs often, replace Network card or clocks

Random XMI000 messages may be generated if excessive Electrostatic Discharges (ESD) are allowed to enter the system. These messages may be safely ignored. Refer to General Maintenance Information (553-3001-500) for ESD avoidance practices.

1. a If message occurs rarely, ignore it.

b. If it occurs often, replace the Controller.

2. a. If message occurs rarely, ignore it.

b. If it occurs often, replace the PS or Network card.

3. a. Check cabling between Controller and Network.

b. Replace the Controller.

c. Replace the Network.

In X11 Release 15 and 16, "FRw APx SQy TPz" is output before the text, where "w" is the loop number. This data is not output in X11 Release 17 and later. Messages without text indicate that the Network or Controller card have requested software download.

XMI, 1999, ?Nortel Networks

回复

使用道具 举报

已有11人评论

新浪微博达人勋

千家认证

沙发
coben 发表于 2004-5-12 19:44:00
北电专家呢?
回复 支持 反对

使用道具 举报

新浪微博达人勋

千家认证

板凳
haozhixi 发表于 2004-5-13 01:45:00

路过 !

解决不了 抱歉 !

回复 支持 反对

使用道具 举报

新浪微博达人勋

千家认证

地板
骑猫的耗子 发表于 2004-5-13 09:12:00
北电什么型号??
回复 支持 反对

使用道具 举报

新浪微博达人勋

千家认证

5#
coben 发表于 2004-5-13 09:42:00
Error message from Nortel 81C
回复 支持 反对

使用道具 举报

新浪微博达人勋

千家认证

6#
jyc7405 发表于 2004-5-13 10:43:00

你注意到没有:

错误出现时的工作CPU是不是同一个?

可能要更换CNI板和相应的PS板哟

回复 支持 反对

使用道具 举报

新浪微博达人勋

千家认证

7#
coben 发表于 2004-5-13 10:56:00

可能要更换CNI板和相应的PS板,好严重呀

回复 支持 反对

使用道具 举报

新浪微博达人勋

千家认证

8#
haozhixi 发表于 2004-5-13 13:33:00

我说大家伙 能不能把 这段 英文故障给翻译一下 哦 !

估计 把它翻译出来 故障的地方就明了 啦!

回复 支持 反对

使用道具 举报

新浪微博达人勋

千家认证

9#
coben 发表于 2004-5-13 13:41:00
我想更换CONTROLLER/XNET卡板试一下
回复 支持 反对

使用道具 举报

新浪微博达人勋

千家认证

10#
骑猫的耗子 发表于 2004-5-14 08:57:00
你们的版本是不是太老了点??
回复 支持 反对

使用道具 举报

新浪微博达人勋

千家认证

11#
coben 发表于 2004-5-14 22:39:00

错误信息是来自网管软件,那是1999年的版本了,很老了,不用管他。系统软件版本是25.40。

到底有没有人遇到过?

回复 支持 反对

使用道具 举报

新浪微博达人勋

千家认证

12#
coben 发表于 2004-5-17 21:55:00
?
回复 支持 反对

使用道具 举报

您需要登录后才可以回帖 登录 | 立即注册 新浪微博登陆 千家通行证登陆

本版积分规则

千家智客微信号
千家智客微信
玩物说商城
玩物说商城