请教一个关于en密码的问题?...

我现在有一台cisco catalyst 2900 series xl 的交换机, en模式的密码忘记了,不知道有什么办法能够解决?哪位大侠帮忙不胜感谢!

[此贴子已经被作者于2004-2-26 14:50:38编辑过]

斑竹干什么呢!怎么不回答我的问题呢?

Description This document describes the password recovery procedure for the Cisco Catalyst 2900-XL and the Cisco Catalyst 3500-XL. Step-by-Step Procedure Attach a terminal or PC with terminal emulation to the console port of the switch. Use the following terminal settings: 9600 baud rate No parity 8 data bits No stop bit Unplug the power cable. Hold down the mode button while reconnecting the power cord to the switch. You can release the mode button a second or two after the LED above port 1x is no longer illuminated. The following instructions appear: The system has been interrupted prior to initializing the flash file system. The following commands will initialize the flash file system, and finish loading the operating system software: flash_init load_helper boot Type flash_init. Type load_helper. Type dir flash:. The switch file system is displayed: Directory of flash: 2 -rwx 843947 Mar 01 1993 00:02:18 C2900XL-h-mz-112.8-SA 4 drwx 3776 Mar 01 1993 01:23:24 html 66 -rwx 130 Jan 01 1970 00:01:19 env_vars 68 -rwx 1296 Mar 01 1993 06:55:51 config.text 1728000 bytes total (456704 bytes free) Type rename flash:config.text flash:config.old to rename the configuration file. This file contains the password definition. Type boot to boot the system. Enter N at the prompt to start the Setup program, Continue with the configuration dialog? [yes/no] : N At the switch prompt type en to turn on enable mode. Type rename flash:config.old flash:config.text to rename the configuration file with its original name. Copy the configuration file into memory. Switch# copy flash:config.text system:running-config Source filename [config.text]? (press Return) Destination filename [running-config]? (press Return) The configuration file is now reloaded. Change the password. switch#config terminal switch(config)#enable password Cisco Write the running configuration to the configuration file. switch(config)#write mem

重起交换机按break键 进入启动方式 覆盖原有系统 然后重起 设置新密码

Type flash_init. Type load_helper. Type dir flash:. The switch file system is displayed: Directory of flash: 2 -rwx 843947 Mar 01 1993 00:02:18 C2900XL-h-mz-112.8-SA 4 drwx 3776 Mar 01 1993 01:23:24 html 66 -rwx 130 Jan 01 1970 00:01:19 env_vars 68 -rwx 1296 Mar 01 1993 06:55:51 config.text 1728000 bytes total (456704 bytes free) Type rename flash:config.text flash:config.old to rename the configuration file. This file contains the password definition. Type boot to boot the system. Enter N at the prompt to start the Setup program, Continue with the configuration dialog? [yes/no] : N At the switch prompt type en to turn on enable mode. Type rename flash:config.old flash:config.text to rename the configuration file with its original name. Copy the configuration file into memory. Switch# copy flash:config.text system:running-config Source filename [config.text]? (press Return) Destination filename [running-config]? (press Return) The configuration file is now reloaded. Change the password. switch#config terminal switch(config)#enable password Cisco Write the running configuration to the configuration file. switch(config)#write mem 以上步骤发生中断,没有办法执行,请教应该如何解决?谢谢!

上面所说的方式,还是不能满足我的要求,请问那位大侠有更好的方法,请写的详细一些!

发生中断的具体情况是否可描述一下

Step-by-Step Procedure Attach a terminal or PC with terminal emulation to the console port of the switch. Use the following terminal settings: 9600 baud rate No parity 8 data bits No stop bit Unplug the power cable. Hold down the mode button while reconnecting the power cord to the switch. You can release the mode button a second or two after the LED above port 1x is no longer illuminated. The following instructions appear: The system has been interrupted prior to initializing the flash file system. The following commands will initialize the flash file system, and finish loading the operating system software: flash_init load_helper boot Type flash_init. Type load_helper. Type dir flash:. The switch file system is displayed: Directory of flash: 2 -rwx 843947 Mar 01 1993 00:02:18 C2900XL-h-mz-112.8-SA 4 drwx 3776 Mar 01 1993 01:23:24 html 66 -rwx 130 Jan 01 1970 00:01:19 env_vars 68 -rwx 1296 Mar 01 1993 06:55:51 config.text 1728000 bytes total (456704 bytes free) Type rename flash:config.text flash:config.old to rename the configuration file. This file contains the password definition. Type boot to boot the system. Enter N at the prompt to start the Setup program, Continue with the configuration dialog? [yes/no] : N At the switch prompt type en to turn on enable mode. Type rename flash:config.old flash:config.text to rename the configuration file with its original name. Copy the configuration file into memory. Switch# copy flash:config.text system:running-config Source filename [config.text]? (press Return) Destination filename [running-config]? (press Return) The configuration file is now reloaded. Change the password. switch#config terminal switch(config)#enable password Cisco Write the running configuration to the configuration file. switch(config)#write mem

flash_init load_helper boot 在执行到boot 命令的时候,重新启动计算机时,直接进入了系统,没有办法去执行下面的操作!