千家论坛_智能建筑与智能家居技术交流社区

标题: [求助]请高手解读路由接口状态! [打印本页]

作者: 9_yinzhi    时间: 2006-3-1 21:33
标题: [求助]请高手解读路由接口状态!
<P>路由:BDCOM 2621,前端是台BR400网桥(把4条E1捆绑8M来用),一直感觉网速又慢又不稳定,所以今天请教高手指点指点,分析分析:</P>
<P>show int</P>
<P>FastEthernet0/0 is up, line protocol is up<br>address is 00e0.0f26.38c8<br>  Interface address is 211.***.***.***/30<br>  MTU 1500 bytes, BW 100000 kbit, DLY 10 usec<br>  Encapsulation ARPA, loopback not set<br>  Keepalive not set<br>  ARP type: ARPA, ARP timeout 04:00:00<br>  60 second input rate 1136390 bits/sec, 275 packets/sec!<br>  60 second output rate 783919 bits/sec, 266 packets/sec!<br>  Full-duplex, 100Mb/s, 100BaseTX, 726508454 ii, 681961421 oi<br>    718603975 packets input, 4127460845 bytes, 200 rx_freebuf<br>    Received 718603975 unicasts, 0 lowmark, 726508454 ri, 20816790 input errors<br>    10693433 overrun, 10123357 CRC, 0 framing, 0 busy, 0 long, 0 discard, 0 throttles<br>    683550219 packets output, 3235919114 bytes, 50 tx_freebd, 0 output errors<br>    0 underrun, 0 collisions, 0 late collisions, 0 deferred, 0 reTx expired<br>    0 resets, 0 lost carrier, 0 no carrier 0 grace stop 0 bus error<br>    0 output buffer failures, 0 output buffers swapped out 0 tx errors</P>
<P>FastEthernet0/1 is up, line protocol is up<br>address is 00e0.0f26.38c9<br>  Interface address is 192.168.1.1/24<br>  MTU 1500 bytes, BW 100000 kbit, DLY 10 usec<br>  Encapsulation ARPA, loopback not set<br>  Keepalive not set<br>  ARP type: ARPA, ARP timeout 04:00:00<br>  60 second input rate 789012 bits/sec, 266 packets/sec!<br>  60 second output rate 1129582 bits/sec, 275 packets/sec!<br>  Full-duplex, 100Mb/s, 100BaseTX, 662024331 ii, 699584101 oi<br>    685296250 packets input, 1675553545 bytes, 199 rx_freebuf<br>    Received 682865940 unicasts, 2896 lowmark, 662024331 ri, 151008 input errors<br>    83786 overrun, 67222 CRC, 0 framing, 2237 busy, 0 long, 0 discard, 0 throttles<br>    717731880 packets output, 914557592 bytes, 50 tx_freebd, 0 output errors<br>    0 underrun, 0 collisions, 0 late collisions, 0 deferred, 0 reTx expired<br>    0 resets, 0 lost carrier, 0 no carrier 0 grace stop 0 bus error<br>    0 output buffer failures, 0 output buffers swapped out 0 tx errors</P>
[此贴子已经被作者于2006-3-1 21:34:51编辑过]


作者: 9_yinzhi    时间: 2006-3-2 12:27
都不理我???!!!




欢迎光临 千家论坛_智能建筑与智能家居技术交流社区 (http://bbs.qianjia.com/) Powered by Discuz! X3.2