[分享]MA5605配置操作手册
<p>MA5605配置操作手册</p><p>相关命令：show time<br/> show version<br/> show board 0<br/> show running-config</p>
<p><br/>1:改名字<br/>MA5605(config)#hostname xiaowei</p>
<p>2:改用户密码<br/>MA5605#user password <br/>>old password: admin<br/>> New password(<20 chars): adminmin（改后新密码，如果不需要设置此步不需要做）<br/>> Confirm new password:adminmin</p>
<p>3:改时间</p>
<p>MA5605#time （一般不用配置）<br/> </p>
<p>4. 进入LAN 配置模式设置LAN 端口状态<br/>int lan 0/0<br/>MA5605(config-LAN-0/0)#port mode<br/><tagged-mode>{tagged,untagged}:tagged<br/>{negotiate,non-negotiate}:non-negotiate<br/>{full-duplex}:full-duplex<br/><speed>{100m}:100m<br/>Set successfully.</p>
<p> </p>
<p>5.MA5605(config-LAN-0/0)#vlan %d (业务VLAN）<br/><vlanId>{1-4095}:1554<br/>Add VLAN successfully, VLANID = </p>
<p>MA5605(config-LAN-0/0)#vlan %d (管理VLAN）<br/><vlanId>{1-4095}:1000<br/>Add VLAN successfully, VLANID = </p>
<p>5. 设置VLAN (打开带内通道)</p>
<p>MA5605(config)#nms <br/><vlanId>{1-4095}:1000（网关vlan）<br/>Are you sure to set the inband VLAN to 1? (y/n) :y</p>
<p><br/>6. 设置级联转发VLAN (注意如果是级连要此步，不是侧不要)<br/>MA5605(config-LAN-0/0)#cascade<br/>{forward,number}:number<br/><num>{0-3}:1<br/>Set cascading number successfully.</p>
<p><br/>MA5605(config-LAN-0/0)#cascade<br/>{forward,number}:forward<br/>{vlan,all}:all<br/><start-vlanId>{1-4095}:<br/><end-vlanId>{1-4095}:<br/>Set 16 cascading VLAN successfully.<br/>注意：<br/>?? 如果有级联设备，则上级设备需要设置转发（下级设备的）VLAN和级联层数（<br/> 设置FE接口级联转发功能”）；<br/>?? 级联MA5605 下级的VLAN ID 必须在上级MA5605 设备分配的范围内。</p>
<p>7. 设置设备IP 地址<br/>MA5605(config)#atmlan ip-address ethernet<br/><ip-addr>:218.92.157.150<br/><netmask>:255.255.255.248<br/>Set successfully</p>
<p><br/>8. 配置到上连设备的系统路由<br/>MA5605(config)#atmlan ip-route<br/><ip-addr>:0.0.0.0<br/><netmask>:0.0.0.0<br/><gateway>:218.92.157.145<br/>Add route successfully.</p>
<p>9. 配置可接受访问列表</p>
<p> <br/>MA5605(config)#atmlan ip-access<br/><start-ip>:218.92.157.145 (路游地址)<br/><end-ip>:218.92.157.137<br/><mask>:255.255.255.255</p>
<p>（可把县局要维护的计算机、交换机地址配置进去）</p>
<p> </p>
<p><br/>10. 设置ADSL 线路模板参数<br/>WA_SL_MA5605(config)#adsl line-profile add 8<br/> During input,press 'Q' to quit,then settings at this time are neglected.<br/> > Select the line profile type 1-adsl 2-adsl2+(1~2) : (2加模板)<br/> > Will you set basic configuration for modem? (y/n) :y<br/> Note: Setting to these mode of G992.3~5 will lead that the adsl ports that are<br/> not support adsl2+ not be activated<br/> > ADSL operating mode:<br/> > 0: All(G992.1~3, G992.5, T1.413)<br/> > 1: Full rate(G992.1/3/5 or T1.413)<br/> > 2: g.lite(G992.2) (ADLI can not support )<br/> > 3: T1.413 (ADLI can not support )<br/> > 4: g.dmt(G992.1/3/5)<br/> > 5: g.hs(G992.1~3, G992.5, G992.5 is prior)<br/> > 6: G992.1<br/> > 7: G992.2 (ADLI can not support )<br/> > 8: G992.3<br/> > 9: G992.5<br/> Please select (0~9) :<br/> > Trellis coding 0-disable 1-enable (0~1) :<br/>> Upstream channel bit swap 0-disable 1-enable (0~1) :<br/> > Downstream channel bit swap 0-disable 1-enable (0~1) : 0<br/> > Will you set channel mode? (y/n) : y<br/> Please select channel mode 0-interleaved 1-fast (0~1) :<br/> > Will you set interleave delay? (y/n) : y<br/> > Max down stream interleaved delay(0~255 ms) :<br/> > Max up stream interleaved delay(0~255 ms) :<br/> > Please select form of transmit rate adaptation in downstream:<br/> > 0-fixed 1-adaptAtStartup 2-adaptAtRuntime (0~2) :<br/> > Will you set noise margin for modem? (y/n) :y<br/> > Target noise margin in down stream (0~15 dB) :<br/> > Min noise margin in down stream (0~6 dB) :<br/> > Max noise margin in down stream (6~31 dB) :<br/> > Target noise margin in up stream (0~15 dB) :<br/> > Min noise margin in up stream (0~6 dB) :<br/> > Max noise margin in up stream (6~31 dB) :<br/> > Will you set parameters for rate? (y/n) : y<br/> > Min bit rate in down stream (32~32000 Kbps) :<br/> > Max bit rate in down stream (32~32000 Kbps) : 7168（下行用户速率）<br/> > Min bit rate in up stream (32~3000 Kbps) :<br/>> Max bit rate in up stream (32~3000 Kbps) : 512（上行速率）<br/> > Please input the profile's name : 9M<br/> Add profile 9 successfully.</p>
<p> </p>
<p><br/>12. 激活ADSL 端口<br/>MA5605(config)#interface adsl 0/1<br/>MA5605(config-ADSL-0/1)#detactivate all<br/>MA5605(config-ADSL-0/1)#activate<br/>{<all>}{all}:all<br/>[<lineprofileindex>]{1-20}:5</p>
<p><br/>13. 设置从ADSL 1 端口到VLAN 10 的业务PVC pvc adsl 0/1/1 8 81 lan 0/0 2335 1483b 1 off off 2 2 (批量生成)<br/>MA5605(config)#pvc<br/>{adsl,shdsl,lan}:adsl<br/><FrameId/SlotId/PortId>{(0)/(1-4)/(1-16)}:0/1/1<br/>{<vpi>}{0-127}:0<br/>{<vci>}{32-127}:100<br/>{adsl,shdsl,lan}:lan<br/><FrameId/SlotId>{(0)/(0-4)}:0/0<br/>{untagged,tagged}:tagged<br/><vlanId>{1-4095}:10<br/>{1483b,ipoa}:1483b<br/><priority>{0-7}:1<br/><rx-car>{off,on}:off<br/><tx-car>{off,on}:off<br/><rx-cttr>{1-20}:2<br/><tx-cttr>{1-20}:2</p>
<p> </p>
<p>15: 保存</p>
<p>MA5605(config)#save</p>
<p> </p>
页:
[1]